Cary Audio Design HD Surround Sound Processor Cinema 11a Owner'S Manual Download Page 49

Page: 49 / 59

SETUP MENU

ZONE 2

Cinema 11a's front panel and main remote handset can control ZONE 2 output sources and

volume control in the SETUP MENU.

- Zone 2

- Zone 2 input

- Zone 2 volume

TO SET ZONE 2 INPUT FROM THE MAIN ZONE REMOTE

Press the SETUP button on the remote to enter the “SETUP MENU”.

The “SETUP MENU / LISTENING PROFILES” menu appears on the front panel display.

Press the

button on the remote until you reach “ZONE 2” on the front panel display.

The “SETUP MENU / ZONE 2” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “ZONE 2” setup menu.
The “ZONE 2 / ZONE 2 Input….INPUT 1” menu appears on the front panel display.

Use the

and

buttons on the remote to select a Zone 2 input source.

You can select INPUT 1, INPUT 2, INPUT 3, INPUT 4, INPUT 5, INPUT 6, INPUT 7,

INPUT 8, 7.1CH ( L & R ONLY) FM, AM, HDFM, HDAM, HDMI 1 and HDMI 2.

Press the

button on the remote to reach “GOTO MAIN MENU”. Once this appears on

the front panel display, press the ENTER button on the remote to return to the SETUP

menu or press the SETUP button to simply exit the SETUP MENU completely.

TO SET ZONE 2 VOLUME FROM THE MAIN ZONE REMOTE

Press the SETUP button on the remote to enter the “SETUP MENU”.

The “SETUP MENU / LISTENING PROFILES” menu appears on the front panel display.

Press the

button on the remote until you reach “ZONE 2” on the front panel display.

The “SETUP MENU / ZONE 2” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “ZONE 2” setup menu.

The “ZONE 2 / ZONE 2 Input….INPUT 1” menu appears on the front panel display.

Press the

button on the remote until you reach the “ZONE 2 Volume” menu.

The “ZONE 2 / ZONE 2 Volume….-30dB” menu appears on the front panel display.

Use the

and

buttons on the remote to select the Zone 2 output volume.

You can adjust the Zone 2 volume level from -90dB to +15dB.

Press the

button on the remote to reach “GO TO MAIN MENU”. Once this appears on

the front panel display, press the ENTER button on the remote to return to the ZONE 2
menu or press the SETUP button to simply exit the SETUP MENU completely.

Summary of Contents for HD Surround Sound Processor Cinema 11a




























































Search results

Summary of Contents for HD Surround Sound Processor Cinema 11a

Reviews:

Related manuals for HD Surround Sound Processor Cinema 11a

Brands by name

Popular brands

Cary Audio Design HD Surround Sound Processor Cinema 11a, Owner'S Manual

Search results

Summary of Contents for HD Surround Sound Processor Cinema 11a

Reviews:

Related manuals for HD Surround Sound Processor Cinema 11a

Brands by name

Popular brands