Cary Audio Design HD Surround Sound Processor Cinema 11a Owner'S Manual Download Page 54

Page: 54 / 59

SETUP MENU

Please follow steps 1 through 3 from the “to set password” instruction above to reach

the “ADVANCED SETTINGS” menu.

Press the

button on the remote until you reach “REAR IR MODE” on the front panel

display.

The “ADVANCED SETTINGS / REAR IR MODE…..Normal” menu appears on the front

panel display.

Use the

and

buttons on the remote to select either the “NORMAL” mode or the

“INVERT” mode. When you select the “NORMAL” mode, the Zone 1 Rear IR remote

control sensor input’s polarity is set as positive. When you select the “INVERT” mode, the

Zone 1 Rear IR remote control sensor input’s polarity is set as negative. This setting

selects the polarity of the Zone 2 rear IR sensor.

To set Zone 2 Rear IR Mode:

When you select NORMAL, the Polarity is positive. When you select INVERT, the Polarity is

negative.

Please follow steps 1 through 3 from the “to set password” instruction above to reach

the “ADVANCED SETTINGS” menu.

Press the

button on the remote until you reach “ZONE2 IR MODE” on the front panel

display.

The “ADVANCED SETTINGS / ZONE2 IR MODE” menu appears on the front panel.

Use the

and

buttons on the remote to select either the “NORMAL” mode or the

“INVERT” mode. When you select the “NORMAL” mode, the Zone 1 Rear IR remote
control sensor input’s polarity is set as positive. When you select the “INVERT” mode, the

Zone 1 Rear IR remote control sensor input’s polarity is set as negative. This setting

selects the polarity of the Zone 2 rear IR sensor.

TO SET 12V TRIGGER OUTPUTS

Please follow steps 1 through 3 from the “to set password” instruction above to reach

the “ADVANCED SETTINGS” menu.

Press the

button on the remote until you reach “TRIGGER….ZONE 1” on the front

panel display.

The “ADVANCED SETTINGS / TRIGGER……ZONE 1” menu appears on the front panel

remote.

Use the

and

buttons on the remote to select which zone controls the 12v trigger

outputs. If you select “ZONE 1”, a 12-volt trigger signal is output when Zone 1 of the

Cinema 11a is powered on. If you select “ZONE 2”, a 12-volt trigger signal is output

when zone 2 of the Cinema 11a is powered on. If you select “ZONE 1 & 2”, a 12-volt

trigger signal is output when either Zone’s 1 or 2 of the Cinema 11a are powered on.

Summary of Contents for HD Surround Sound Processor Cinema 11a




























































Search results

Summary of Contents for HD Surround Sound Processor Cinema 11a

Reviews:

Related manuals for HD Surround Sound Processor Cinema 11a

Brands by name

Popular brands

Cary Audio Design HD Surround Sound Processor Cinema 11a, Owner'S Manual

Search results

Summary of Contents for HD Surround Sound Processor Cinema 11a

Reviews:

Related manuals for HD Surround Sound Processor Cinema 11a

Brands by name

Popular brands