manualshive.com logo in svg

Carlisle Ransburg DynaFlow 77376, Service Manual, Page: 62 / 96

Share
Download
Carlisle Ransburg DynaFlow 77376 Service Manual Download Page 62

Displayed Text

Fault Cause

Corrective Action

ERROR CODES

 (Cont.)

Code

TROUBLESHOOTING GUIDE

 (Cont.)

B020

B030

B040

B050

B060

RIO - Invalid
BTW Type

RIO - Invalid
BTR Type

Gun/Channel
Number

RIO - Invalid 
BTR Job 
Number

RIO - Invalid
BTW Length

The PLC has issured a BTW with an 
invalid BTW data type in the first word 
offset.

The PLC has issued a BTW with an 
invalid BTR data type in the second 
word offset.

The PLC has issued a BTW with an 
invalid gun or channel number in the 
third word offset.

The PLC has issued a BTW with an 
invalid  job  number  in  the  fourth  word 
offset.

The PLC has issued a BTW with an 
invalid message length (word count).

Have the PLC programmer reference the 
"DynaFlow Programmer" manual for the correct 
BTW data types.

Have the PLC programmer reference the 
"DynaFlow Programmer" manual for the correct 
BTR data types.

Have the PLC programmer ensure gun and 
channel numbers are between 1 and 8, or 0 if 
not required for the particular data type.

Have the PLC programmer ensure job numbers 
are between 1 and 100, or 0 if not required for 
the particular data type.

Have the PLC programmer reference the 
"DynaFlow Programmer" manual for the correct 
BTW message lengths.

Return To Contents

LN-9400-00-R11  (08/2018)

62 / 96

www.carlisleft.com

MAINTENANCE

Summary of Contents for Ransburg DynaFlow 77376

































































































Reviews:

No comments