manualshive.com logo in svg

Carlisle Ransburg DynaFlow 77376, Service Manual, Page: 60 / 96

Share
Download
Carlisle Ransburg DynaFlow 77376 Service Manual Download Page 60

Displayed Text

Fault Cause

Corrective Action

ERROR CODES

 (Cont.)

Code

TROUBLESHOOTING GUIDE

 (Cont.)

(Continued On Next Page)

External GUN 
ENABLE Input Not 
Detected

24 VDC must be supplied to the external 
GUN ENABLE input before the GUN 
can be placed in an active state. This 
is typically used as an interlock with 
other equipment or hard-wired directly 
to 24 VDC.

Check for 24 VDC on the external GUN EN-
ABLE input.

9081
9082
9083
9084
9085
9086
9087
9088

9091
9093
9095
9097

Channels Not 
Present

Channel Module is not installed or 
has failed.

1.  Insert Channel Module or change 
  GUN configuration.
2.  Reboot system and check again.
3.  Replace Channel Module.

9111

9112
9113
9114
9115
9116
9117
9118

Out of Tolerance - 
Catalyst Too High
CHANNEL #<>

The indicated slave (catalyst) CHANNEL 
is above it's maximum tolerance limit as 
specified  by  the  FLOW  TOLERANCE 
parameter.

Check the following:
1.  Kp or Ki gains set too high.
2.  Running the wrong JOB #, which may include 

the wrong gain values.

3.  Fluid pressures. Either reduce the catalyst supply 

pressure or increase the resin pressure. Try to 
maintain normal operating pilot pressures to the 
fluid regulators, between 30-60 psi.

4.  The MVR LOW JOB parameter for the catalyst 

is set too high (above the regulator cracking 
pressure).

5.  Air bubbles or cavitation.

Last digit indicates 

CHANNEL #

.

9211

9212
9213
9214
9215
9216
9217
9218

Out of Tolerance - 
Catalyst Too Low
CHANNEL #<>

The indicated slave (catalyst) CHANNEL 
is below it's minimum tolerance limit as 
specified  by  the  FLOW  TOLERANCE 
parameter.

Check the following:
1.  Kp or Ki gains set too low.
2.  Running the wrong JOB #, which may include 

the wrong gain values.

3.  Fluid pressures. Either increase the catalyst 

supply pressure or decrease the resin pressure. 
Try to maintain normal operating pilot pressures 
to the fluid regulators, between 30-60 psi.

4.  Requested flow rate exceeds capability of the 

catalyst channel at the given fluid supply pressure. 
Reduce total flow rate or increase catalyst supply 
pressure.

5.  Air bubbles or cavitation.

Last digit indicates 

CHANNEL #

.

Return To Contents

LN-9400-00-R11  (08/2018)

60 / 96

www.carlisleft.com

MAINTENANCE

Summary of Contents for Ransburg DynaFlow 77376

































































































Reviews:

No comments