Canon NP6251 Service Bulletin Download Page 6

Page: 6 / 67

SERVICE BULLETIN COPIER

NP6251

MODEL:

Major quality issues

Field quality problems

Quality upgrade/production efficiency

Miscellaneous

LOCATION:

SUBJECT:

Issued by Canon Europa N.V.

DECK PICK-UP ASSEMBLY

IMPROVEMENT TO DURABILITY OF SEPARATION ROLLER

Outline

A bearing has been added to the separation roller support to improve the roller durability.

Details

[Phenomenon]

Paper pick-up fault

[Cause]

The sponge part of the separation roller becomes damaged because of a decrease in durability.

[Factory measures]

A bearing has been added to the separation roller support .

Measures for servicing

If the above phenomenon occurs, replace the parts below or the deck pick-up assembly.

- 1/3 -

FB2-7602-000 (replace)

New part

Old part

Deck right pick-up assembly

FF5-3213-000 (replace)

FB3-9207-000

FF5-6397-000

XG9-0243-000 (new)

FB3-9207-000

FS6-2678-000

FB2-7602-000 (replace)

FS5-2983-000 (replace)

No.:

6251-003 Rev. 1
(H2-12E-033)

DATE: 24.07.98

Summary of Contents for NP6251




































































Search results

Summary of Contents for NP6251

Reviews:

Brands by name

Popular brands

Canon NP6251, Service Bulletin

Search results

Summary of Contents for NP6251

Reviews:

Brands by name

Popular brands