Canon NP6251 Service Bulletin Download Page 38

Page: 38 / 67

1 / 3 -

Service Bulletin

Issued by Canon Europa N.V.

Model :

NP6251

No.:

6251-014 Rev. 2

(FF-T01-H2-000029-02)

DATE:

10.12.99

Location

MAIN DRIVE ASSEMBLY

Subject

MECHANISM TO DETECT FRAGMENTS OF PAPER REMAINING AT FIXING/DELIVERY

UNIT REAR SIDE

Reason

Papers jammed at the holding tray assembly may be pinched in the contact section of the

transfer/separation corona assembly; a mechanism has been added to detect this condition. For

information on preventing jams at the holding tray assembly, see Service Bulletin 6251-008 Rev. 2.

Details

A microswitch for jam paper detection has been installed near the main unit side contact section (main

drive assembly) of the transfer/separation corona assembly. This microswitch displays error code

“E013”* upon detecting jammed papers.

*: E013 code originally served the purpose of detecting waste toner feedscrew error. Now, this code is

also used to detect paper jams.

Servicing

: The position and installation procedure for the paper jam detection mechanism are shown below.

Remove the transfer assembly high voltage connector (FH2-9164-000) at the rear of the high voltage

transformer PCB assembly and install the new part at this position. (See Fig. 1.)

COPIER

High voltage transformer

PCB assembly

High voltage connector

Fig. 1 High voltage connector position

Summary of Contents for NP6251




































































Search results

Summary of Contents for NP6251

Reviews:

Brands by name

Popular brands

Canon NP6251, Service Bulletin

Search results

Summary of Contents for NP6251

Reviews:

Brands by name

Popular brands