Canon NP6251 Service Bulletin Download Page 3

Page: 3 / 67

- 3/4 -

6251-001

5) If the screwdriver does not go through the oval hole on the cam plate, loosen the fixing screw of the cam

plate and move the cam plate in the Y direction, then put the screwdriver through the oval hole. (See
Figures 6 and 7.)

6) With the screwdriver through the oval hole, tighten the cam fixing screw by lightly pressing the cam shaft

(shaded part of Figure 8) against the side of the rail (toward the lens).

7) After attaching the removed parts, turn the power switch ON and check the image for DIRECT copying.

If good resolution is not obtained, repeat Steps 1 to 6 again. When good resolution is obtained, bond lock
the cam plate fixing screw.

Fig. 8 Fixing cam shaft

Fig. 6 Lens stage

Fig. 7 Positional relationship of round hole and oval

hole when the lens side hole is seen from the top

Y direction

Cam plate

Cam plate
fixing screw

Cam shaft

Lens

Oval

hole

Round

hole

Summary of Contents for NP6251




































































Search results

Summary of Contents for NP6251

Reviews:

Brands by name

Popular brands

Canon NP6251, Service Bulletin

Search results

Summary of Contents for NP6251

Reviews:

Brands by name

Popular brands