manualshive.com logo in svg

Canon NP6251, Service Bulletin

Share
Download
Canon NP6251 Service Bulletin Download Page 22

SERVICE BULLETIN

COPIER

Issued by Canon Europa N.V.

MODEL:

NP6251

No.:

6251-007 Rev. 1

(A9800572-02)

Date: 10.08.99

SUBJECT:

HEATER LAMP/CANON GIESSEN MADE MACHINE

There are discrepancies between the configuration of the Canon Giessen made machine and the
documentation in the Parts Catalog. Since the specifications of the Canon Giessen made machine to
comply with the radio interference controls were not determined in time for the initial edition of the Parts
Catalog, inclusion of the information from that edition was not possible.

From the first mass production machine of the Canon Giessen made 220V/240V machines, two
heaters have been installed to comply with the flicker and harmonic controls which are part of the radio
interference controls.
The major differences in part numbers between the Parts Catalog and the Canon Giessen made
220/240V machine are listed in the table below.

Description

Parts Catalog

GSN 220V/240V

Q’ty

Heater H1

FH7-4441-000

FH7-4551-000

1

Heater H2

----

FH7-4552-000

1

Fixing unit

FG5-8639-000

FG5-9819-000

1

AC driver

FG5-8864-000

FG6-0036-020

1

DC power supply

FG5-4510-030

FG6-1572-000

1

Lamp regulator

FH3-7173-000

FH3-7205-000

1

DC Controller PCB Ass’y

FG5-9312-000

FG5-9825-030

1

Note: The way to mount the heaters is the same as the way they are mounted for 100V/115V/120V

machines.

Next time the Parts Catalog is revised, we will update it with the above information.

Summary of Contents for NP6251




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands