manualshive.com logo in svg

Canon MultiPASS C100, User Manual

Share
Download
Canon MultiPASS C100 User Manual Download Page 165

Chapter 13

Troubleshooting

13-9

T

roub

leshooting

Message

Error Code Cause

Action

INSTALL BC33/30

INSTALL BC33/34

K INK EMPTY

LOAD PAPER

M INK EMPTY

MEMORY FULL

—

—

—

—

—

#037

You disabled the 

PHOTO

INK PRINT

setting 

(

1

p. 14-8) and tried to

make a black & white
copy, print a received
black & white fax, print a
report, or print a black &
white document in
memory with the installed
Photo BJ cartridge.

You tried to make a
colour copy with the
installed Black BJ
cartridge.

The Black BJ tank in the
Colour, Photo, or Black
BJ cartridge is empty.

The multi-purpose tray is
empty.

The Magenta BJ tank in
the Colour or Photo BJ
cartridge is empty.

The unit’s memory is full
because it has received
too many documents, or
a very long or detailed
document.

Replace the BJ cartridge
with the Colour or Black BJ
cartridge (

1

p. 12-12).

Alternatively, enable the

PHOTO INK PRINT

setting.

(

1

p. 14-8)

Replace the BJ cartridge
with the Colour or Photo
BJ cartridge. (

1

p. 12-12)

Replace the BJ tank 
(

1

p. 12-18). The unit will

then print automatically any
faxes received in memory.

Load paper in the multi-
purpose tray (

1

p. 2-17).

Make sure the stack is
below the paper limit mark
(

P

). Then press Resume.

Replace the BJ tank 
(

1

p. 12-18). The unit will

then print automatically any
faxes received in memory.

Print any documents stored
in memory (

1

pp. 7-17, 

8-11, 8-13). Then start
again.

Summary of Contents for MultiPASS C100



















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands