manualshive.com logo in svg

Canon MultiPASS C100, User Manual

Share
Download
Canon MultiPASS C100 User Manual Download Page 160

13-4

Troubleshooting

Chapter 13

Jams in the Multi-Purpose Tray

If print media jams in the multi-purpose tray, the LCD displays 

CLEAR PAPER JAM

.

Follow this procedure to clear the jam:

n

You do not need to unplug the unit when clearing paper jams.

1

Close the document tray if necessary.

2

Gently pull any jammed paper out of
the unit as shown.

3

Remove the paper stack from the multi-
purpose tray and reload it. (

1

p. 2-17)

• Make sure the stack does not exceed the

paper limit mark (

P

).

4

Press Resume to start the operation
again.

• If you are printing from a Windows

®

application, follow the instructions displayed
by the software on your PC.

n

If the paper jam occurred while a fax was being received into the MultiPASS’ memory, that
fax will print automatically when the jam is cleared and you press Resume.

Summary of Contents for MultiPASS C100



















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands