Canon iR2318 series Service Manual Download Page 98

Page: 98 / 308

Chapter 3

3-4

3.3.2 Configration of Image processing Module

0020-4213

The main image processing of this equipment is executed by the Main controller PCB (main).

Following is the related module configuration.

F-3-4

3.3.3 Reader entry Image processing

0020-4214

The image processor PCB performs the image processing to the image data read at the contact image sensor.

F-3-5

DDR

Reader controller PCB

-image memory
-Temporary strage of program

Image Processor PCB

DC controller PCB

Reader Unit

This performs the image
processing against the
image data read at the reader unit

Reader entry image processing area

This performs the image processing
to output the image to printer

Printer output image processing area

To the compression/expansion/edit processing block

correction

- Mirror image processing

- Magnification chage processing
- Brightness density correction
- Even out variation

Image processor PCB

Reader unit

Summary of Contents for iR2318 series





















































































































































































































































































































Search results

Summary of Contents for iR2318 series

Reviews:

Canon iR2318 series, Service Manual, Page: 98 / 308

Search results

Summary of Contents for iR2318 series

Reviews: