manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 113 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 113

Chapter 4

4-7

The functional configuration of the reader controller PCB is shown below.

F-4-5

4.1.8 Reader Controller PCB (When the original size detection sensor is not equipped for BOOK mode)

0020-4226

Jack No. 

Function

J401

Supplies power (24 VDC) from the main body (printer). 

J402

Supplies power (5 VC, 3.3 VDC) from the main body (printer). 

J403

Communicates with the main body (printer) (to control the ADF).

J404

Communicates with the main body (printer). 

J405

Connected to the copyboard open/close sensor. 

J406

Connected to the contact image sensor (CIS) HP sensor. 

J407

Connected to the original sensor 1 and original sensor 2.

J408

Connected to the contact image sensor (CIS).

J409

Connected to the reader motor. 

J410

Supplies power to the ADF. 

J411

Communicates with the ADF (to drive the sensor).

J412

Communicates with the ADF (to drive the motor).

J413

Connected to the original sensor 3, original sensor 4, and original sensor 5.

J409

J412

J411

J403

J404

J405

J402

IC1

J408

J407

J413

J406

J410

IC9

J401

DC24V

DC3.3V

DC5V

IC2

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments