manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 19 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 19

Contents

Contents

1.1 System Construction ......................................................................................................................................................1-1

1.1.1 Pickup/ Delivery /Original Handling Accessories System Configuration (1-cassette/Platen cover (option) model) ................. 1-1
1.1.2 Pickup/ Delivery /Original Handling Accessories System Configuration (1-cassette/Platen cover (standard) model) .............. 1-2
1.1.3 Pickup/ Delivery /Original Handling Accessories System Configuration (2-cassette/Duplex unit (option) model) .................. 1-3
1.1.4 Pickup/ Delivery /Original Handling Accessories System Configuration (2-cassette/Duplex unit (standard) model) ............... 1-4
1.1.5 Reader Heater/ Cassette Heater System Configuration ............................................................................................................... 1-5
1.1.6 Printing/Transmitting Accessories System Configuration........................................................................................................... 1-5

1.2 Product Specifications....................................................................................................................................................1-6

1.2.1 Names of Parts ............................................................................................................................................................................. 1-6

1.2.1.1 External View (1-cassette model)  ..................................................................................................................................................................1-6
1.2.1.2 External View (2-cassette model) ...................................................................................................................................................................1-6
1.2.1.3 Cross-Section ..................................................................................................................................................................................................1-7

1.2.2 Using the Machine ....................................................................................................................................................................... 1-8

1.2.2.1 Turning On the Power Switch (1-cassette model)  .........................................................................................................................................1-8
1.2.2.2 Turning On the Power Switch (2-cassette model) ..........................................................................................................................................1-9
1.2.2.3 When Turning Off the Main Power Switch (1-cassette model) ...................................................................................................................1-10
1.2.2.4 When Turning Off the Main Power Switch (2-cassette model)....................................................................................................................1-12
1.2.2.5 Control Panel.................................................................................................................................................................................................1-13

1.2.3 User Mode Items........................................................................................................................................................................ 1-14

1.2.3.1 Audible Tones ...............................................................................................................................................................................................1-14
1.2.3.2 Common Settings ..........................................................................................................................................................................................1-15
1.2.3.3 Copy Settings ................................................................................................................................................................................................1-16
1.2.3.4 Printer Settings ..............................................................................................................................................................................................1-16
1.2.3.5 Timer Settings ...............................................................................................................................................................................................1-17
1.2.3.6 Timer Settings ...............................................................................................................................................................................................1-17
1.2.3.7 Adjustment/Cleaning.....................................................................................................................................................................................1-17
1.2.3.8 Report Settings ..............................................................................................................................................................................................1-17
1.2.3.9 System Settings .............................................................................................................................................................................................1-18
1.2.3.10 Network Settings.........................................................................................................................................................................................1-19

1.2.4 Maintenance by the User ........................................................................................................................................................... 1-20

1.2.4.1 User Maintenance Items................................................................................................................................................................................1-20
1.2.4.2 Cleaning ........................................................................................................................................................................................................1-21

1.2.5 Safety ......................................................................................................................................................................................... 1-22

1.2.5.1 Safety of the Laser Light...............................................................................................................................................................................1-22
1.2.5.2 CDRH Regulations........................................................................................................................................................................................1-22
1.2.5.3 Handling the Laser Unit ................................................................................................................................................................................1-23
1.2.5.4 Safety of Toner..............................................................................................................................................................................................1-23
1.2.5.5 Point to Note about Fire ................................................................................................................................................................................1-23

1.2.6 Product Specifications ............................................................................................................................................................... 1-24

1.2.6.1 Product Specifications...................................................................................................................................................................................1-24

1.2.7 Function List .............................................................................................................................................................................. 1-25

1.2.7.1 Printing Speed (iR2422series).......................................................................................................................................................................1-25
1.2.7.2 Printing Speed (iR2420/iR2320series)..........................................................................................................................................................1-26
1.2.7.3 Printing Speed (iR2318series).......................................................................................................................................................................1-27

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments