manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 21 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 21

Chapter 1

1-1

1.1 System Construction

1.1.1 Pickup/ Delivery /Original Handling Accessories System Configuration (1-cassette/Platen cover (option) model)

0020-4194

The configuration is as shown in the following figure:

F-1-1

*1: A Cassette feeding module-S1 can be placed on the Cassette feeding module-T1 to use these cassette units as a 3-stage cassette unit.

*2: This accessory is required when the Finisher-U2, Cassette feeding module-T1 is installed.

[1]

DADF-P2

[2]

Platen Cover Type J

[3]

Finisher-U2

[4]

Additional Finisher Tray-C1

[5]

Inner 2-way Tray-E2

[6]

Cassette Feeding Module-S1

*1

[7]

Cassette Feeding Module-T1

*1

[8]

Duplex Unit-A1

[9]

Power Supply Kit-Q1

*2

[10]

Document Tray-J1

[3]

[2]

[10]

[4]

[5]

[7]

[7]

[6]

[6]

[1]

[8]

[9]

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments