manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 217 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 217

Chapter 9

9-7

9.4 Parts Replacement Procedure

9.4.1 External Covers

9.4.1.1 Delivery Tray

9.4.1.1.1 Removing the Delivery Tray

0020-4455

1) Detach the rear cover.

2) Open the front cover.

3) Detach the right cover (lower).

4) Detach the delivery tray [1].

- Screw [2] 2 pcs. 

F-9-9

9.4.1.2 Right Cover (Lower)

9.4.1.2.1 Removing the Right Cover (Lower)

0020-4457

1) Remove the rear cover.

2) Open the front cover [1].

3) Remove the two hooks [2], and then detach the right cover (lower) [3].

- Screws [4] 5 pcs.

F-9-10

9.4.1.3 Right Cover (Upper)

9.4.1.3.1 Removing the Right Cover (Upper)

0020-4461

1) Remove the rear cover.

2) Open the front cover.

3) Remove the right cover (lower).

4) Remove the right cover (upper) [1].

- Screw [2] 1 pc.

F-9-11

9.4.1.4 Rear Cover

9.4.1.4.1 Removing the Rear Cover

0020-4464

1) Remove the rear cover [1].

- Screws [2] 4 pcs.

F-9-12

9.4.1.5 Left Cover (Lower)

9.4.1.5.1 Removing the Lower-left Cover

0020-4466

1) Detach the lower-left cover [2] by opening the rear support [1] with a

slightly strong force applied in the direction of the arrow.

F-9-13

[2]

[1]

[4]

[3]

[1]

[2]

[2]

[1]

[2]

[1]

[2]

[2]

[1]

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments