manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 133 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 133

Chapter 4

4-27

4)Remove the screw [1].

5) Remove the reader heater (right) [2].

- Wire saddle [3] 1 pc.

- Connector [4] 1 pc.

F-4-65

4.4.8.2 Removing the Reader Heater (Left) (When the 

ADF is not installed)

0022-0966

1) Open the copyboard cover. 

2) Remove the reader front cover.

3) Remove the cover [1].

- Screws [2] 5 pcs.

4) Pull the drive belt (front) [3] in the direction of the arrow to move the con-

tact sensor [4] to the center.

F-4-66

5) Remove the metal plate [1].

- Screws [2] 2 pcs.

F-4-67

6) Remove the heater cover [1].

- Screw [2] 1 pc.

F-4-68

7) Remove the reader heater (left) [1].

- Connector [2] 1 pc.

- Screw [3] 1 pc.

F-4-69

4.4.8.3 Removing the Reader Heater (Left) (When the 

ADF is installed)

0020-4409

1) Open the ADF.

2) Remove the reader front cover.

3) Remove the glass retainer.

4) Remove the ADF reading glass.

MEMO:

Illustrations of this procedure are figured the document size sensor equipped 
model, but procedure is same as document size sensors are not equipped 
model.

[3]

[1]

[4]

[2]

[4]

[1]

[3]

[2]

MEMO:

Illustrations of this procedure are figured the document size sensor equipped 
model, but procedure is same as document size sensors are not equipped 
model.

[1]

[2]

[2]

[1]

[2]

[3]

[1]

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments