manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 263 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 263

Chapter 13

13-3

E733

0000

Erroneous communication between controller and printer 

Cannot communicate with the printer 
at startup.

- Check the connectors of the DC controller 
PCB and image processor PCB for normal 
connection. 
- Check the power supply of the printer 
(Check whether initialization is performed at 
startup). 
- Replace the DC controller PCB or image 
processor PCB. 

E805

0000

Fan failure

The fan is faulty. 

- Check the fan connector. 
- Replace the fan.
- Replace the DC controller PCB.

E808

0000

Fixing drive circuit failure

- The heater does not turn on.
- A fixing drive motor failure was 
detected. 

- Check the connector of the fixing film unit. 
- Replace the fixing film unit. 
- Replace the fixing drive motor. 
- Replace the DC controller PCB.
- Replace the power supply PCB. 

Display 
Code

Detail Code Main Cause/Symptom

Countermeasure

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments