Canon iR2318 series Service Manual Download Page 39

Page: 39 / 308

Chapter 1

1-19

1.2.3.10 Network Settings

0021-9502

Item

Setting Description

Default Setting

TCP/IP Settings

IPv4 Settings: IP Address Settings

IP Address Auto.

DHCP

On/Off

Off

BOOTP

On/Off

Off

RARP

On/Off

Off

IP Address

IP address

0.0.0.0

Subnet Mask

IP address

0.0.0.0

Gateway Address

IP address

0.0.0.0

IPv4 Settings

PING Command

IP address

0.0.0.0

IPv4 Settings

IP Address Range

On/Off
Up to four IPv4 addresses or ranges of IPv4
addresses can be stored. (Permit/Reject)

Off

IPv4 Settings: DNS Settings

DNS Server Settings

Primary DNS Server

IP address

0.0.0.0

Secondary DNS Server

IP address

0.0.0.0

DNS Host/Domain

Host Name

47 Characters maximum

('Canon' + the last six digits of the machine's MAC
address)

Domain Name

47 Characters maximum

(NULL)

DNS Dynamic Update

On/Off

Off

IPv6 Settings

Use IPv6

On/Off

Off

Stateless Address

On/Off

IPv6 Settings: Manual Address Set.

Use Manual Address

On/Off

Off

Manual Address

39 Characters maximum

0:0:0:0:0:0:0:0

Prefix Length

0 to 128

Default Router Addr.

39 Characters maximum

0:0:0:0:0:0:0:0

IPv6 Settings

Use DHCPv6

On/Off

Off

IPv6 Settings: PING Command

IPv6 Address

39 Characters maximum

0:0:0:0:0:0:0:0

Host Name

48 Characters maximum

(NULL)

IPv6 Settings

IP Address Range

On/Off
Up to 4 IPv6 addresses, ranges of IPv6
addresses, or IPv6 address prefixes can be
stored. (Permit/Reject)

Off

IPv6 Settings: DNS Settings

DNS Server Settings

Primary DNS Server

IP address

0.0.0.0

Secondary DNS Server

IP address

0.0.0.0

DNS Host/Domain

On/Off

Use IPv4 Host/Domain

On/Off

Off

Host Name

47 Characters maximum

('Canon' + the last six digits of the machine's MAC
address)

Domain Name

47 Characters maximum

(NULL)

DNS Dynamic Update

On/Off

Off

Reg. Manual Address

On/Off

Off

On/Off

Off

WINS Configuration

On/Off

Off 0.0.0.0

Summary of Contents for iR2318 series





















































































































































































































































































































Search results

Summary of Contents for iR2318 series

Reviews:

Canon iR2318 series, Service Manual, Page: 39 / 308

Search results

Summary of Contents for iR2318 series

Reviews: