Canon imageRUNNERC1022, Service Manual

Page: 108 / 534

Chapter 2
2-12
2.5.6 Installation Procedure in the imageWARE
Accounting Manager (hereinafter referred to iWAM)
Environment
0020-3780
imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER
C1030 / Color imageRUNNER C1030iF
1) Select "ON" in [Additional Func.] > [System Management Set.] > [Dept.
ID Management] and press [Set] key.
Check to see that "0000001 to 0001000" has been created in [Register
Dept. ID/Pass.]. (In the case that "1" is entered as the first number in the
following item: Service Mode > COPIER > OPTION > ACC > CARD.)
2) Press 'Back' key or 'Done' key to exit [Additional Func.].
3) Make the setting for network in [Additional Func.] > [System Manage-
ment Set.] > [Network Settings] > [TCP/IP Settings] > [IPv4 Settings] >
[IP Address Settings].
- In the case of [Manual Settings], make the setting of [IP Address],
[Subnet Mask], [Gateway Address] according to the environment of user.
- In the case of [Obtain Automatically], select either of the following;
[DHCP], [BOOTP], [RARP].
4) Press 'Back' key or 'Done' key to exit [Additional Func.].
5) Turn off and then on the main power switch.
6) Enter a number for [System Mgmt. Dept. ID] and [System Mgmt. Pass-
word] in [Additional Func.] > [System Management Set.] > [System
Manager Info. Set.], and then press [Register] key.
7) Press 'Back' key or 'Done' key to exit [Additional Func.].
2.6 Installing the Hand Set
2.6.1 Points to Note At Installation
0020-1359
imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER
C1030 / Color imageRUNNER C1030iF
2.6.2 Checking the Contents
0020-0535
imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER
C1030 / Color imageRUNNER C1030iF
<Handset-J1>
F-2-28
2.6.3 Turning OFF the Power of the Host Machine
0020-0538
imageRUNNER C1022 / imageRUNNER C1022i
1) Turn OFF the main power.
2) Remove the power plug (for outlet).
2.6.4 Installation Procedure
0020-0539
imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER
C1030 / Color imageRUNNER C1030iF
1) Remove the 2 face seals [1]. (The removed face seals are not used.)
F-2-29
2) Install the handset adapter [1].
- 2 plasti rivets [2]
NOTE:
Pressing [Network Settings] displays the following message. Press [Done]
key to exit the screen that displays this message.
[Changes become effective after the main power switch is turned OFF and
ON again.]
CAUTION:
Note that 'Registration of card to the device' cannot be executed in setting
of iWAM unless [Additional Func.] > [System Management Set.] >
[System Manager Info. Set.] is selected and [System Mgmt. Dept. ID] and
[System Mgmt. Password] are registered.
CAUTION:
When installing this equipment, make sure that the FAX board is installed
first.
[1] Handset 1pc
[2] Handset rest 1pc
[3] Handset adapter 1pc
[4] Plasti rivet 4pc
[5] Wire saddle 3pc
[1] [2] [3]
[4] [5]
[1]