Canon imagePROGRAF W7200 User Manual Download Page 139

Page: 139 / 187

Message Is Displayed

7-15

Feed Limit

Problem 1:

You pressed

on the operation panel to feed more media than allowed.

Solution:

Open the tray, then turn the roll holder manually to feed the extra media.

Size Undetected

Problem 1:

The media has shifted out of the correct load position, or the media is
curled.

Solution:

Set the media correctly. (

P.2-8, P.2-20)

Problem 2:

The printer interior is dusty or dirty.

Solution:

Open the upper cover and clean inside the printer. (

P.6-11)

Remove Ink Tank

Problem 1:

Right cover was closed without removing the ink tank.

Solution:

Remove the ink tank.

Turn Power Off!!

Problem 1:

The tape inside the upper cover or the belt stopper have not been removed.

Solution:

Switch the printer off, open the upper cover, remove the tape and belt
stopper, then press the Power button. (

Setup Guide)

Problem 2:

The printer has malfunctioned.

Solution:

Switch the printer off, then press and hold down the Power button for over
3 seconds to switch the printer on again.

Solution:

If the message occurs again after switching the printer off and on, note the
message in the first line of the operation panel display, then call for
service.

W-Ink Full Soon

Problem 1:

The waste ink tank is nearly full and requires replacing very soon.

Solution:

Printing can continue after this message is displayed. However, you should
call for service as soon as possible before a Service Call is issued.

Summary of Contents for imagePROGRAF W7200




























































































































































































Search results

Summary of Contents for imagePROGRAF W7200

Reviews:

Related manuals for imagePROGRAF W7200

Brands by name

Popular brands

Canon imagePROGRAF W7200, User Manual

Search results

Summary of Contents for imagePROGRAF W7200

Reviews:

Related manuals for imagePROGRAF W7200

Brands by name

Popular brands