Canon imagePRESS C1 P, Service Manual, Page: 877 / 1265

Chapter 15
15-14
E5F6 There is an error in saddle butting (saddle finisher).
8001 The paper pushing plate home position sensor does not turn on
when the paper pushing plate motor has been driven for 0.3 sec or
more.
Paper pushing plate motor (M8S)/the paper pushing plate home
position sensor (PI14S)
Check the paper pushing plate motor (M8S)/the paper pushing
plate home position sensor (PI14S).
8002 The paper pushing plate home position sensor does not turn off
when paper pushing plate motor has been driven for 80 msec or
more.
Paper pushing plate motor (M8S)/the paper pushing plate home
position sensor (PI14S)
Check the paper pushing plate motor (M8S)/the paper pushing
plate home position sensor (PI14S).
8003 The number of detection pulses of the paper pushing plate motor
clock sensor drops below a specific number.
Paper pushing plate motor (M8S)/the paper pushing plate motor
clock sensor (PI1S)
Check the paper pushing plate motor (M8S)/the paper pushing
plate motor clock sensor (PI1S)
8004 The paper pushing plate sensor does not turn off when the paper
pushing plate motor has been driven for 80 msec or more.
Paper pushing plate motor (M8S)/the paper pushing plate leading
edge position sensor (PI15S)
Check the paper pushing plate motor (M8S)/the paper pushing
plate leading edge position sensor (PI15S)
8005 The paper pushing plate leading edge position sensor does not turn
on when the paper pushing plate motor has been driven for 0.3 sec
or more.
Paper pushing plate motor (M8S)/the paper pushing plate leading
edge position sensor (PI15S)
Check the paper pushing plate motor (M8S)/the paper pushing
plate leading edge position sensor (PI15S)
E5F8 There is an error in the saddle connector (saddle finisher).
0001 The connector of the guide home position sensor is identified as
being disconnected.
The connector of the guide home position sensor (PI13S)
Check the connectors of the guide home position sensor (PI13S).
0002 The connector of the paper pushing plate home position sensor is
identified as being disconnected.
The connector of the paper pushing plate home position sensor
(PI14S)
Check the connectors of the paper pushing plate home position
sensor (PI14S).
0003 The connector of the paper pushing plate leading edge position
sensor is identified as being disconnected.
The connector of the paper pushing plate leading edge sensor
(PI15S)
Check the connectors of the paper pushing plate leading edge
sensor (PI15S).
E5F9 There is an error in the saddle switch (saddle finisher).
0001 With any of the following sensor is identifying its respective cover
a being closed, the inlet cover switch is identified as being open for
1 sec or more after the start of the initial rotation of the machine or
the start of printing:
-inlet cover sensor (PI9S)
-front cover open/closed sensor (PI2S)
-delivery cover sensor (PI3S)
Or, the front cover switch (MS2S) or the delivery cover switch
(MS3S) is open.
The inlet cover switch (MS2S)/front cover switch (MS2S)/
delivery cover switch (MS3S9)
Check the inlet cover switch (MS1S)/front cover switch (MS2S)/
delivery cover switch (MS3S).
0002 With any of the following sensor is identifying its respective cover
a being closed, the front cover switch is identified as being open
for 1 sec or more after the start of the initial rotation of the machine
or the start of printing:
-inlet cover sensor (PI9S)
-front cover open/closed sensor (PI2S)
-delivery cover sensor (PI3S)
-front cover switch(MS2S)/delivery cover switch (MS3S)
Check the front cover switch (MS2S)/delivery cover switch
(MS3S).
0003 With any of the following sensor is identifying its respective cover
a being closed, the delivery cover switch is identified as being
open for 1 sec or more after the start of the initial rotation of the
machine or the start of printing:
-inlet cover sensor (PI9S)
-front cover open/closed sensor (PI2S)
-delivery cover sensor (PI3S)
-delivery cover switch (MS3S)
Check the delivery cover switch (MS3S).
E602 There is a hard disk error
There is a fault in hard disc.
(See 'HDD Error Remedy' of the main controller)
E604 There is a shortage of image memory (SDRAM).
0000 The amount of memory required by the model in question is not
recognized.
Set it to the size of memory suited to the model in question.
0001 The shortage of memory for MEAP application.
MEAP application is installed despite of the Base model
-Modify the configuration to make MEAP as Full model. After
executing uninstallation of the application (i.e., downloading of
the license), set it as MEAP Base.
-Modify the configuration to make MEAP as Full model.
0002 Overload of the image memory. Remove the expanded main memory.
Turn off and then on the main power.
1024/1536 Fault/lacking in image memory Set it to the size of memory suited to the model in question.
Turn off and then on the main power.
Code Cause (Detection Description) Remedy