38
Manual de instrucciones y lista de repuestos
Lista de Repuestos
Modelo WS2800
1
Etiquetas de Advertencia
DK683400AV
1
2
Conector Dinse
WC000200AV
2
3
Enchufe Dinse
WC000300AV
2
4
Cordón de energía – 230V, 50A (NEMA 6-50P),
7 pies (213 cm), 12AWGX3C, Tipo SJT
*
1
5
Cable de soldar – 5 AWG (15mm2) x 10 pies (305 cm)
WC000800AV
2
6
Pinza de trabajo – 250A
WC100100AV
1
7
Liberador de tensión
WC102400AV
1
8
Portaelectrodo – 300A
WC200200AV
1
9
Mango
WC301600AV
1
10
Tapón del tubo – 9,94" (24mm) OD
WC301601AV
2
11
Tornillo de la máquina – M4-0.7 X 35 mm (Mango)
*
4
12
Manivela, Juego de (incluye manivela, perilla, perno, arandelas y tuerca)
WC302300SJ
1
13
Interruptor de energía
WC402400AV
1
14
Interruptor térmico
WC402500AV
1
15
Luz indicadora – Verde
WC402600AV
1
16
Luz indicadora – Amarilla
WC402700AV
1
17
Ventilador
WC402800AV
1
18
Eje
WC704300AV
1
19
Contratuerca
WC704301AV
2
20
Rueda
WC704400AV
2
21
Rueda giratoria
WC704500AV
2
22
Tornillo de la máquina – M4-0,7 X 10 mm (Rueda giratoria)
*
8
23
Puerta
WC705100AV
1
24
Pasador de la bisagra
WC705300AV
2
25
Puntero del medidor
WC705500AV
1
26
Rejilla del ventilador
WC706200AV
1
27
Pasador de la puerta
WC706300AV
1
28
Lentes de soldar – Oscuros 10, 2x4-1/4" (51x108mm)
WC801100AV
1
29
Protector manual
WC801300AV
1
30
Martillo/cepillo cincelador
WC803000AV
1
* Piezas estándar, disponibles en su tienda local de venta de ferretería o suministros de soldar.
No se muestra
No. de
Ref.
Descripción
Número
Ctd.
Figura 16 - Repuestos
Para mayor información
sobre este producto
llame al 1-800-746-5641
(desde los E.E.U.U.)
1
13
15
17, 26
16
3
12
14 (dentro
de la caja)
4
9
10
11
7
18
19
20
21
22
23
27
24
25
2
5
8
6
Park, Quincy, MA 02269
Safe Practices For Occupational And
Educational Eye And Face Protection
ANSI Standard Z87.1, from American
National Standards Institute, 1430
Broadway, New York, NY 10018
Refer to the Material Safety Data Sheets
and the manufacturers instructions for
metals, electrodes, coatings and
cleaners.
Installation
LOCATION
Selecting the proper location can
significantly increase performance,
reliability and life of the arc welder.
For best results locate the welder in
an environment that is clean and dry.
Avoid locations exposed to high
temperature, high humidity, dust
and corrosive fumes. High humidity
causes moisture condensation on
electrical components. Moisture can
contribute to corrosion and short
electrical components. Dust and dirt
in the welder retain moisture and
increase wear of moving parts.
Place the welder in an area that
provides at least twelve inches (305
mm.) of ventilation space at both the
front and rear of the unit. Keep all
obstructions away from this
ventilation space.
Store electrodes in a clean, dry
location with low humidity, such as
WT2240 Electrode Container, to
preserve the flux coating.
The welder control panel contains
information regarding proper input
voltage and amperage. Follow the
specifications on the welder front
panel.
The receptacle used for the welder
must be properly grounded and the
welder must be the only load on the
power supply circuit. Refer to the
Circuit Amps chart under
Specifications for correct circuit
capacity.
The use of an extension cord is not
recommended for electric arc
welding machines. The voltage drop
in the extension cord may
significantly degrade the
performance of the welder.
Fire
hazard!
Do not weld on containers
or pipes that contain or
have contained flammable
materials or gaseous or liquid
combustibles.
Arc
welding
closed cylinders or
containers such as tanks or
drums can cause explosion if
not properly vented! Verify that any
cylinder or container to be welded has
an adequate ventilation hole, so that
expanding gases can be released.
Do not
breathe
fumes that are produced by
the arc welding operation.
These fumes are
dangerous. If the welding area cannot
be adequately ventilated, be sure to
use an air-supplied respirator.
Keep the head and face out of the
welding fumes.
Do not perform electric arc welding
operations on metals that are
galvanized or cadmium plated, or
contain zinc, mercury, or beryllium
without completing the following
precautions:
a. Remove the coating from the
base metal.
b. Make sure that the welding area
is well ventilated.
c. Use an air-supplied respirator.
Extremely toxic fumes are created
when these metals are heated.
The
electro-
magnetic field that is
generated during arc
welding may interfere with the
operation of various electrical and
electronic devices such as cardiac
pacemakers. Persons using such devices
should consult with their physician
prior to performing any electric arc
welding operations.
Route the electrode and work
cables together and secure with
tape when possible.
Never wrap arc welder cables
around the body.
Always position the electrode and
ground leads so that they are on
!
WARNING
!
WARNING
!
WARNING
!
WARNING
Model WS2800
the same side of the body.
Exposure to electromagnetic fields
during welding may have other
health effects which are not known.
Always be sure
that the welding
area is secure and free of hazards
(sparks, flames, glowing metal or slag)
prior to leaving. Be sure that
equipment is turned off and electrode
is removed. Be sure that cables are
loosely coiled and out of the way. Be
sure that all metal and slag has cooled.
• This product, when used for welding,
produces fumes or gases which
contain chemicals known to the State
of California to cause birth defects
(or other reproductive harm) and, in
some cases, cancer (California Health
& Safety Code Section 25249.5 et
seq.).
• To request Material Safety Data Sheet
(MSDS), visit the Internet at
www.chpower.com or call
1-800-746-5641.
ADDITIONAL SAFETY STANDARDS
ANSI Standard Z49.1
from American
Welding Society, 550 N.W. LeJune Rd.
Miami, FL 33126
Safety and Health Standards
OSHA 29 CFR 1910, from
Superintendent of Documents, U.S.
Government Printing Office,
Washington, D.C. 20402
National Electrical Code
NFPA Standard 70, from National Fire
Protection Association, Batterymarch
Park, Quincy, MA 02269
Safe Handling of Compressed Gases
in Cylinders
CGA Pamphlet P-1, from Compressed
Gas Association, 1235 Jefferson Davis
Highway, Suite 501, Arlington, VA
22202
Code for Safety in Welding and
Cutting
CSA Standard W117.2, from Canadian
Standards Association, Standards Sales,
178 Rexdale Boulevard, Rexdale,
Ontario, Canada M9W 1R3
Cutting And Welding Processes
NFPA Standard 51B, from National Fire
Protection Association, Batterymarch
!
WARNING
!
WARNING
www.chpower.com
3
