background image

General Safety Information

CALIFORNIA PROPOSITION 65

 

This product or its

 power cord may 

contain chemicals, including lead, 
known to the State of California to 
cause cancer and birth defects or other 
reproductive harm. Wash hands after 
handling.

  You 

can 

 create 

dust when you cut, sand, drill 
or grind materials such as 
wood, paint, metal, concrete, 
cement, or other masonry. This dust 
often contains chemicals known to 
cause cancer, birth defects, or other 
reproductive harm. Wear protective 
gear.

GENERAL SAFETY

 Since the air compressor and other 
components (material pump, spray 
guns, filters, lubricators, hoses, 
etc.) used, make up a high pressure 
pumping system, the following safety 
precautions must be observed at all 
times:

 1.  Read all manuals included 

with this product 
carefully. Be thoroughly 
familiar with the 
controls and the proper use of the 
equipment.

2.  Follow all local electrical and safety 

codes as well as in the United States, 
the National Electrical Codes (NEC) 
and Occupational Safety and Health 
Act (OSHA).

3.  Only persons well acquainted with 

these rules of safe operation should 
be allowed to use the compressor.

4.  Keep visitors away and NEVER allow 

children in the work area.

5.  Wear safety glasses and 

use hearing protection 
when operating the unit.

6.  Do not stand on or use the unit as a 

handhold.

7.  Before each use, inspect compressed 

air system and electrical components 
for signs of damage,  deterioration, 
weakness or leakage. Repair or 
replace defective items before 
using.

8.  Check all fasteners at frequent 

intervals for proper tightness.

 Motors, 

  electrical 

equipment and controls can 
cause electrical arcs that 
will ignite a fl ammable gas 
or vapor. Never operate or repair in or 
near a fl ammable gas or vapor. Never 
store fl ammable liquids or gases in the 
vicinity of the compressor.

 

 

Compressor parts may be hot 
even if the unit is stopped.

 9.  Keep fingers away from a 

running compressor; fast moving 
and hot parts will cause injury and / 
or burns.

10. If the equipment should start 

to vibrate abnormally, STOP 
the engine / motor and check 
immediately for the cause. Vibration 
is generally a warning of trouble.

11. To reduce fire hazard, keep 

engine / motor exterior free of oil, 
solvent, or excessive grease.

 

  A safety relief valve

 with a setting no 

higher than 125 psi MUST be installed 
in the tank for this compressor. The 
safety valve must have suffi cient fl ow 
and pressure ratings to protect the 
pressurized components from bursting.

 See 

compressor 

  specifi cation decal 

for maximum operating pressure. 
Do not operate with pressure switch 
or pilot valves set higher than the 
maximum operating pressure.

12. Never attempt to adjust the safety 

valve. Keep safety valve free from 
paint and other accumulations.

 

Never use plastic

 (PVC) pipe for 

compressed air. Serious injury or death 
could result.

 Never 

  attempt 

to repair or modify a tank! 
Welding, drilling or any other 
modifi cation will weaken the 
tank resulting in damage from rupture 
or explosion. Always replace worn, 
cracked or damaged tanks.

 

Drain liquid from 

 tank daily.

 13. Tanks rust from moisture build-up, 

which weakens the tank. Make 
sure to drain tank regularly and 
inspect periodically for unsafe 
conditions such as rust formation 
and corrosion.

14. Fast moving air will stir up dust 

and debris which may be harmful. 
Release air slowly when draining 
moisture or depressurizing the 
compressor system.

15. Indoor use only.

16. To reduce the risk of electrical 

shock, do not expose to rain. Store 
indoors.

SPRAYING PRECAUTIONS

 Do 

not 

   spray 

fl ammable materials in 
vicinity of open fl ame 
or near ignition sources 
including the compressor unit.

 17. Do not smoke when spraying paint, 

insecticides, or other flammable 
substances.

18. Use a face mask / 

respirator when spraying 
and spray in a well 
ventilated area to prevent 
health and fire hazards.

19. Do not direct paint or other sprayed 

material at the compressor. Locate 
compressor as far away from 
the spraying area as possible to 
minimize overspray accumulation 
on the compressor.

20. When spraying or cleaning with 

solvents or toxic chemicals, follow 
the instructions provided by the 
chemical manufacturer.

MANUAL

2

www.campbellhausfeld.com

Breathable Air Warning 

This compressor / pump is not equipped and should not be used “as is” 
to supply breathing quality air. For any application of air for human 
consumption, the air compressor / pump will need to be fitted with 
suitable in-line safety and alarm equipment. This additional equipment 
is necessary to properly filter and purify the air to meet minimal 
specifications for Grade D breathing  as described in Compressed 
Gas Association Commodity Specification G 7.1 - 1966, OSHA 29 
CFR 1910.134, and/or Canadian Standards Associations (CSA).

DISCLAIMER OF WARRANTIES
In the event the compressor is used for the purpose of breathing air 
application and proper in-line safety and alarm equipment is not 
simultaneously used, existing warranties shall be voided,  and the 
Manufacturer disclaims any liability whatsoever for any loss, personal 
injury or damage.

Operating Instructions and Parts List

FP1995 Series

Summary of Contents for FP1995 Series

























Reviews: