Camfil CleanSeal Exhaust V3 Installation & Operating Manual Download Page 28

Page: 28 / 63

EMC_SPEC040_CLCR.doc

Rev. E

–

2021 10 18

28/63

Install & Operating Manual

CleanSeal V3

Installation of Add-ons

9.1

Dampers

PLEASE NOTE:

The installation of either shut-off or regulation dampers as standard add-ons

requires

a “damper ready” S

-C-housing or a customized T-C-housing.

Interface parts like the adapter rod and locking screws are included as accessories

with the housing.

Dampers are packed separately from the housing.

➔

For shut-off dampers

discard fixing screws

➔

For regulation dampers

replace with

s washers

from damper accessory kit

and adjust to desired friction strength

➔

Adjust dampers from the technical area above
by turning the damper handle

or

➔

from the room below
by turning the adapter rod











2,5

Summary of Contents for CleanSeal Exhaust V3
































































Search results

Summary of Contents for CleanSeal Exhaust V3

Reviews:

Related manuals for CleanSeal Exhaust V3

Brands by name

Popular brands

Camfil CleanSeal Exhaust V3, Installation & Operating Manual

Search results

Summary of Contents for CleanSeal Exhaust V3

Reviews:

Related manuals for CleanSeal Exhaust V3

Brands by name

Popular brands