Cambium Networks PTP 820 Series Installation Manual Download Page 6

Page: 6 / 179

Installation Guide for RFU-D-HP

Page 6 of 179

List of Figures

Figure 1: RFU-D-HP Radio Interfaces ................................................................................................................. 15

Figure 2: RFU-D-HP Front Side Interfaces .......................................................................................................... 15

Figure 3: RFU-D-HP Data and Power Interfaces ................................................................................................ 16

Figure 4: RFU-D-HP Rear View (Left) and Front View (Right) ............................................................................ 16

Figure 5: Cable Gland Construction ................................................................................................................... 17

Figure 6: RFU-D-HP Radio Unit .......................................................................................................................... 18

Figure 7: RFU-D-HP Diplexer Unit ...................................................................................................................... 18

Figure 8: OMT .................................................................................................................................................... 19

Figure 9:Space Diversity Branching Device ....................................................................................................... 19

Figure 10: Splitter .............................................................................................................................................. 20

Figure 11: Dual Coupler/Splitter/Circulator ...................................................................................................... 20

Figure 12: Remote Pole Mount ......................................................................................................................... 21

Figure 13: Remote Pole Mount Adaptor ........................................................................................................... 21

Figure 14: RFU-D-HP OCU Unit .......................................................................................................................... 22

Figure 15: RFU-D-HP Branching Pole Profile (Part of RFU-D-HP Filters Remote Mount Kit) ............................. 22

Figure 16: Short U-Bend .................................................................................................................................... 23

Figure 17: Long U-Bend ..................................................................................................................................... 23

Figure 18: Splitter/Coupler ................................................................................................................................ 23

Figure 19: Termination ...................................................................................................................................... 23

Figure 20: Cable Grounding ............................................................................................................................... 32

Figure 21: Cable Design ..................................................................................................................................... 40

Figure 22: Tightening the Front Portion of the Gland ....................................................................................... 47

Figure 23: Tightening the Rear Portion of the Gland ........................................................................................ 47

Figure 24: Transparent Pressure Windows ....................................................................................................... 59

Figure 25: RFU-D-HP Installation

–

Attaching the Diplexers Unit Before the Radio Unit .................................. 62

Figure 26: Fitting the Diplexer Unit to the Radio Unit - Radio Side .................................................................. 64

Figure 27: Fitting the Diplexer Unit to the Radio Unit - Diplexer Unit Side ...................................................... 64

Figure 28: Radio and Diplexer Units Together .................................................................................................. 64

Figure 29: Hook and Carrying Handle ................................................................................................................ 65

Figure 30: Securing the Diplexer Unit to the Radio Unit ................................................................................... 65

Figure 31: Remote Pole Mount Kit

–

6-11 GHz.................................................................................................. 72

Figure 32: Remote Pole Mount Kit

–

4-5 GHz .................................................................................................... 72

Figure 33: Remote Pole Mount Kit

–

6-11 GHz.................................................................................................. 72

Figure 34: Remote Pole Mount Kit

–

4-5 GHz .................................................................................................... 72

Summary of Contents for PTP 820 Series




















































































































































































Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands

Cambium Networks PTP 820 Series, Installation Manual

Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands