Cambium Networks PTP 820 Series Installation Manual Download Page 71

Page: 71 / 179

Installation Guide for RFU-D-HP

Page 71 of 179

Adaptor
Remote
Mount
Kit

DXDH-RM-MOUNT-ADPT-

Circ./Cir
c.
Adaptor

Per Antenna Vendor. Not used for standard interface antennas (six feet and larger).

Required Tools

•

Metric offset hexagon key set

•

Metric wrench key set

Common Installation

Prior to the installation, follow the antenna manufacturer’s instructions

for using the circular transition (adaptor).

Remove the existing rectangular transition, swap the O-ring, and install the circular transition instead.

Connect the OMT kit to the antenna and secure it with four screws.

Important Note!

Verify that the O-ring is properly mounted between the antenna transition and the OMT.

Summary of Contents for PTP 820 Series




















































































































































































Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands

Cambium Networks PTP 820 Series, Installation Manual

Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands