manualshive.com logo in svg

Cambium Networks PTP 820 Series, Installation Manual

Share
Download
Cambium Networks PTP 820 Series Installation Manual Download Page 13

Installation Guide for RFU-D-HP 

 

Page 13 of 179 

 

 

Caring for the environment

 

The following information describes national or regional requirements for the disposal of Cambium Networks supplied 
equipment and for the approved disposal of surplus packaging. 

In EU countries

 

The following information is provided to enable regulatory compliance with the European Union (EU) directives 
identified and any amendments made to these directives when using Cambium equipment in EU countries. 

 

Disposal of Cambium equipment 

European Union (EU) Directive 2002/96/EC Waste Electrical and Electronic Equipment (WEEE) 

Do not dispose of Cambium equipment in landfill sites. For disposal instructions, refer to 

http://www.cambiumnetworks.com/support

 

Disposal of surplus packaging 

Do not dispose of surplus packaging in landfill sites. In the EU, it is the individual recipient’s responsibility to ensure t

hat 

packaging materials are collected and recycled according to the requirements of EU environmental law. 

In non-EU countries 

In non-EU countries, dispose of Cambium equipment and all surplus packaging in accordance with national and regional 
regulations. 

Summary of Contents for PTP 820 Series




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands