Cambium Networks PTP 820 Series Installation Manual Download Page 80

Page: 80 / 179

Installation Guide for RFU-D-HP

Page 80 of 179

Required Tools

•

Metric offset hexagon key set

•

Metric wrench key set

Procedure

1 Prior

to the installation, follow the antenna manufacturer’s instructions to use the circular adaptor.

(Remove the existing rectangular transition, swap the O-ring, and install the circular transition instead.)

2 Connect the RFU-D-HP OMT Kit to the antenna and secure it with four screws. Verify existence of the O-

ring.

Note:

Verify that the O-ring is properly mounted between the antenna transition and the OMT.

3 Connect the RFU-D-HP Dual Coupler Kit to the OMT Kit using four M8 screws and washers, and tighten

the screws.

Note:

Verify that the O-rings are properly mounted between the OMT ports and the dual coupler.

Summary of Contents for PTP 820 Series




















































































































































































Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands

Cambium Networks PTP 820 Series, Installation Manual

Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands