Cambium Networks PTP 820 Series Installation Manual Download Page 62

Page: 62 / 179

Installation Guide for RFU-D-HP

Page 62 of 179

General Radio Installation

The RFU-D-HP has been designed for easy installation, with various installation options to provide maximum flexibility.

In most cases, the Diplexers unit should be attached to the antenna or mediation device first. Then, attach the radio
unit to the Diplexers unit.

Figure 25: RFU-D-HP Installation

–

Attaching the Diplexers Unit Before the Radio Unit

The RFU-D-HP radio can also be assembled to the diplexers kit prior to installation, then mounted to the antenna or
mediation device as a single unit. For details, see

Installing the Diplexer on the Radio

on page 63.

Summary of Contents for PTP 820 Series




















































































































































































Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands

Cambium Networks PTP 820 Series, Installation Manual

Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands