Cambium Networks cnPilot Home R200 Series User Manual Download

Page: 51 / 136

Web Configuration

pmp-0884 (September)

3-9

Bridge Mode

Bridge Mode under Multi WAN is different with traditional bridge setting. Bridge mode employs no IP addressing

and the device operates as a bridge between the WAN port and the LAN port. Route Connection has to be built to
give IP address to local service on device.

Under is example of bridge mode:

1_TR069_VOICE_INTERNET_R_VID_ is router connection for local service. 2_Other_B_VID_ is bridge

connection for host of LAN port.

Table 19 Bridge Mode

Field Name

Description

Bridge Type

IP Bridge

Allow all Ethernet packets to pass. PC can connect to upper network directly.

PPPoE Bridge

Only Allow PPPoE packets pass. PC needs PPPoE dial-up software.

Hardware IP Bridge

Packets pass through hardware switch with wired speed. Does not support wireless
port binding

DHCP Service Type

Pass Through

DHCP packets can be forwarded between WAN and LAN, DHCP server in gateway
will not allocate IP to clients of LAN port.

Summary of Contents for cnPilot Home R200 Series









































































































































Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands

Cambium Networks cnPilot Home R200 Series, User Manual

Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands