Cambium Networks cnPilot Home R200 Series User Manual Download Page 54

Page: 54 / 136

Web Configuration

pmp-0884 (September)

3-12

Multi WAN Setting

Overview

Multi WAN is used to implement the distribution of different kinds of services, and device’s Multi WAN supports

the distribution of data services, voice services and management services. By setting different VLANs, different
kinds of data is distributed to the corresponding networks.

For example, INTERNET and Other VLAN supports data transmission, VOICE VLAN supports voice transmission and

TR069 VLAN supports WEB, Telnet and TR069 services transmission.

Figure 3 Multi VLAN

There are several advanced functions available when using Multi WAN setting:

•

PPPoE Bridge allows PPPoE-only packets to pass, which can prohibit Layer 2 packets from flooding the device
LAN ports.

•

Hardware Bridge operates as a Layer 2 Switch to increase throughput between WAN and LAN.

•

VLAN Trunk allows tagged packets to be switched to LAN ports directly.

•

IPTV may be supported with other VLAN-configured LAN ports.

Figure 4 Multi WAN network

Content

Define

Comment

1 to 99

WAN Connection identifier

Summary of Contents for cnPilot Home R200 Series









































































































































Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands

Cambium Networks cnPilot Home R200 Series, User Manual

Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands