Cambium Networks cnPilot Home R200 Series User Manual Download Page 121

Page: 121 / 136

Web Configuration

pmp-0884 (September)

3-79

Procedure

Step 1. Enable Daylight Savings Time.

Step 2. Set value of offset for Daylight Savings Time

Step 3: Set starting Month/Week/Day/Hour in Start Month/Start Day of Week Last in Month/Start Day of

Week/Start Hour of Day, analogously set stopping Month/Week/Day/Hour in Stop Month/Stop Day of Week Last
in Month/Stop Day of Week/Stop Hour of Day.

Step 4.Press Saving button to save and press Reboot button to active changes.

System Log Setting

Field Name

Description

Syslog Enable

Enable/Disable syslog function

Syslog Level

Select the system log, there is INFO and Debug two grades, the Debug INFO
can provide more information.

Remote Syslog Enable

Enable/Disable remote syslog function.

Remote Syslog server

Add a remote server IP address.

Summary of Contents for cnPilot Home R200 Series









































































































































Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands

Cambium Networks cnPilot Home R200 Series, User Manual

Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands