Cambium Networks cnPilot Home R200 Series User Manual Download

Page: 4 / 136

The following describes how warnings and cautions are used in this document and in all documents of the Cambium

Networks document set.

Warnings

Warnings precede instructions that contain potentially hazardous situations. Warnings are used to alert the reader to

possible hazards that can cause loss of life or physical injury. A warning has the following format:

Cautions

Cautions precede instructions and are used when there is a possibility of damage to systems, software, or individual items

of equipment within a system. However, this damage presents no danger to personnel. A caution has the following format:

Notes

A note means that there is a possibility of an undesirable situation or provides additional information to help the reader

understand a topic or concept. A note has the following format:

pmp-0884 (September)

III

Contents

Summary of Contents for cnPilot Home R200 Series









































































































































Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands

Cambium Networks cnPilot Home R200 Series, User Manual

Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands