Cambium Networks cnPilot Home R200 Series User Manual Download Page 24

Page: 24 / 136

Overview

pmp-0884 (September)

1-8

Warning

Please

not

attempt

use

unsupported power

adapters

and

not

remove

power

during configuring

updating

the

cnPilot Home

R200x/R201x

device.

Using other power adapters

may

damage

the

cnPilot Home R200x/R201x and

will

void the

manufacturer

warranty.

Warning

Changes

modifications not

expressly

approved

the party responsible

for

compliance

can

void the

user’s authority

operate

the

equipment.

This equipment

has

been tested and

found to

comply

with

the

limits for

Class B

digital device,

pursuant

Part 15

the

FCC

Rules. These limits

are designed

provide

reasonable

protection

against

harmful

interference

residential

installation.

This equipment

generates,

uses and

can

radiate

radio

frequency energy and, if

not

installed

and

used in

accordance with the

instructions,

may cause harmful

interference to

radio communications.

However,

there is

no guarantee

that interference

will

not

occur in

particular

installation.

If this

equipment

does cause harmful

interference

radio

television

reception,

which can

determined by

turning

the

equipment

off

and

on,

the user is

encouraged

try

correct

the

interference by

one

more of

the

following

measures:

Reorient

relocate

the

receiving

antenna.

Increase

the

separation

between

the

equipment

and

receiver.

Connect

the

equipment

into

outlet on

circuit

different

from that to

which the

receiver

connected.

Consult

the

dealer or

experienced

radio/TV

technician for

help.

Voice Prompt

Summary of Contents for cnPilot Home R200 Series









































































































































Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands

Cambium Networks cnPilot Home R200 Series, User Manual

Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands