background image

11

 ON      DHW     CH     FAULT

2

1

0

1

2

3

4

bar

20

11

14

19

18

17

15

16

13

12

23

21

22

3

9

4

7

10

8

6

5

2

1

24

1. Frame

2. Expansion vessel

3. Electronic regulator

4. 2-way modulating valve (primary heating)

5. Heating flow temperature probe (secondary)

6. DHW heat exchanger

7. 2-way modulating valve - DHW 

8. Thermal safety thermostat 

9. Secondary heating drain cock 

10. DHW temperature probe

11. Filling unit with backflow preventer 

12. Safety relief valve

13. Flow temp. compensation return probe

14. Primary circuit drain cock

15. Pump UPM3 15-70

16. Protective by-pass

17. Pressure switch

18. Heating strainer (secondary)

19. DHW priority flow meter

20. Heating exchanger

21. Heat meter spacer template

22. Primary circuit strainer/flow probe pocket 

23. Primary air vent cock

24. Primary circuit shut-off valves

SATK30

105HE

Indirect HIU with high efficiency pump. 65 kW DHW.

Characteristic components

Factory settings

The SATK30105HE HIU is factory set to support 

low temperature

heating (25–45°C), according to the following switch setting.

To  modify  the  factory  settings  and  enable  the  HIU  to  support

medium/high  temperature

systems  (45–75°C),  proceed  as

follows.

1 - cut off the electric power supply to the HIU

2 - set switches 2-3 according to the following setting:

3 -

disconnect  the  thermal  safety  thermostat  (see  page  13 

ref.  5)  and  apply  a  jumper  on  the  cable  (see  adjacent

diagram)

4 -  restore the electric supply.

Functional characteristics

Heating range

- LOW temperature setting 25–45°C

- MEDIUM/HIGH temperature setting 45–75°C

Set point regulation 

DHW production range 42–60°C

Optional functions

Domestic cycle: 

- DHW pre-heating function

Heating cycle:

- modulating temperature regulation

with compensated set point

at LOW temperature setting:

- floor slab heating function

1

2

3

5

6

4

ON

1

2

3

5

6

ON

4

Factory set (do not change)

OFF

ON

OFF

ON

May be changed to activate optional functions
Switch 1:  modulating  temperature  regulation

with compensated set point

Switch 2-3: HIGH - LOW temperature setting

Switch 5:  DHW pre-heating function

Summary of Contents for SATK30 Series

















Reviews: