background image

5

Hydraulic connections

Hydraulic connections to the centralised line must be implemented

using the manual shut-off valves supplied with the HIU, which allow

any necessary maintenance work to take place without having to

empty the centralised system.

It is advisable to install manual shut-off valves (not supplied) also

on the bottom connections to the apartment circuits.

Before installation, it is recommended to carry out accurate flushing

of  all  the  pipes  of  the  system  in  order  to  remove  any  residue  or

impurities that could endanger correct operation of the HIU.

In  order  to  facilitate  these  operations  a  manual  bypass  flushing

valve is available (code 789100).

N.B. Install the valves as shown in the figure

 ON      DHW     CH     FAULT

2

1

0

1

2

3

4

bar

 ON      DHW     CH     FAULT

2

1

NOTES

:

1 Install water hammer arresters to compensate for any overpressure in the domestic water circuit;
2 In  the  presence  of  hot  water  recirculation  or  if  a  non-return  valve  is  fitted  into  the  domestic  cold  water  inlet,  provision  must  be  made  to

accommodate the expansion of the water contained within the system and the heat interface unit;

3 All hydraulic connections must be checked before pressurising the system. Vibration during transport may cause the connections to become loose.

DO NOT APPLY EXCESSIVE TIGHTENING TORQUE otherwise the components may be damaged.

Key to symbols

 

 

 

 

 

 

   

 

 

 

 

Primary circuit flow

Primary circuit return

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Domestic hot water outlet

Domestic cold water inlet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Low temperature circuit flow

Low temperature circuit return

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

High temperature circuit flow

High temperature circuit return

Summary of Contents for SATK30 Series

















Reviews: