background image

SATK20 & SATK30

1

These instructions must be read and understood
before installing and maintaining the HIU.
CAUTION! FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN A SAFETY
HAZARD!

1

The device must be installed, commissioned and 
maintained by qualified technical personnel in accordance 
with national regulations and/or relevant local 
requirements.

2

If the device is not installed, commissioned and maintained
correctly in accordance with the instructions provided in 
this manual, it may not work correctly and may endanger 
the user.

3

Flush the pipework thoroughly before installing the HIU to 
remove any particles, rust, incrustations, limescale, welding
slag and any other contaminants.        
The water circuits must be clean and free from debris.

4

Make sure that all connection fittings are watertight.

5

When connecting water pipes, make sure that threaded 
connections are not mechanically overstressed. Over time 
this may result in breakage, causing water damage and/or 
personal injury.

C

ontent

Function and product range

1

Safety instructions

1

Dimensions and technical specification

3

Installation

4

First operation

5

Electronic controller

6

Safety and alarms

7

SATK20103 and SATK20203 components

8

SATK20303 components

10

SATK30103 components

12

SATK30105 components

12

Maintenance

14

Electric connections

16

Trouble shooting and solution

17

Product Range

SATK20103

Direct wall-mounted HIU for 

LOW

temperature 

heating, instantaneous domestic hot water
production.

SATK20203

Direct wall-mounted HIU for 

MEDIUM

temperature heating, instantaneous domestic 
hot water production.

SATK20303

Direct wall-mounted HIU for 

HIGH

temperature 

heating, instantaneous domestic hot water 
production.

SATK30103

Indirect wall-mounted HIU, instantaneous DHW 
production - with 

50 kW

heat exchanger.

SATK30105

Indirect wall-mounted HIU, instantaneous DHW 
production - with 

75 kW

heat exchanger.

Safety Instructions

SATK20

SATK30

Function

SATK20 and SATK30 Heat Interface Units (HIU) control the
heating and domestic hot water generation in an individual
apartment within a centralised boiler or district heating system.

NOTE:

Due to the specification ordered, or the country of

destination, the actual unit may differ from those shown.

WARNING

Summary of Contents for Altecnic SATK20





















Reviews: