background image

SATK20 & SATK30

15

Operating Cycles SATK30

Domestic water generation: DHW preheating function

The domestic water preheating function is signalled by the
flashing yellow DHW LED.

This function is less of a priority than any domestic water or
heating cycles.

Heating cycle

Modulating temperature regulation with compensated set
point - LOW temperature setting

The function is enabled by setting dip switch 1 to the OFF
position.

When the function is enabled, the flow temperature is modified
according to the temperature detected by the compensation
probe.

This keeps the actual thermal output of the under floor - and
therefore the ambient thermal load - under control. The
thermal response time of the system is thus minimised.

Safety and alarms

Error codes associated with faults signalled by the lighting up of
the FAULT LED are also shown on the display (see page 7).

Operating Cycles SATK30

Maintenance

All maintenance procedures should be carried out by an
authorised technician.

Regular maintenance guarantees better efficiency and helps to
save energy.

Before carrying out any maintenance, repair or part
replacement work, proceed as follows:

Switch off the electric supply

Remove the cover

Close the shut-off valves

Empty the HIU using the drain cocks provided.

Heat exchanger replacement

Remove the heat exchanger, loosening the 2 hex head 
screws fixing it in place (A)

Replace the heat exchanger and the O-rings.

Tighten the two fixing screws (A).

NOTE:

The pins fixing the heat exchanger are positioned in such

a way as to allow it to be placed only in the correct direction.

Strainer cleaning

All HIU’s have a strainer on the inlet water from the
centralised heating system and for the SATK30103 and
SATK30105, a second strainer is located on the secondary
   circuit.

To clean these strainers, carry out the following maintenance

procedure:

Unscrew the cap (B).

Remove the strainer mesh, flush thoroughly with clean 

water to remove debris.

Replace the strainer mesh.

Screw the cap back into position.

1

OFF

60

4

A

A

B

Summary of Contents for Altecnic SATK20





















Reviews: