background image

Hi Flow Stroller Technical Service Manual • PN 14314465 Rev 

F

3

H

i F

lo

w S
tr

oller

Equipment Description

III

CAIRE, Inc.’s Hi Flow Stroller is the portable component of the 

Liberator/Portable supplementary oxygen system. Enclosed in 

a durable simulated leather case, Hi Flow Strollers incoporate a 

stainless steel cryogenic container with the valves, plumbing, and 

associated hardware required to deliver gaseous oxygen to the pa-

tient at near ambient temperature.

The Hi Flow Stroller is comprised of five major assemblies, 

grouped according to function.

1. Cryogenic Container – This assembly is a double walled,

vacuum insulated dewar for storing liquid oxygen at approxi-

mately -180°C (-300° F).

2. Breathing Circuit – This circuit consists of the manifold as-

sembly, fixed orifice rotary flow control valve (FCV) and

vaporizing coil. It withdraws liquid oxygen from the cryo-

genic container, warms it to near ambient temperature, and

regulates the flow of oxygen gas to the patient. Water that

condenses on the cold coils is collected and absorbed by the

condensate pad.

3. Case Assembly – The case houses and protects the cryogenic

container, the breathing circuit, and the liquid level meter.

4. Liquid Level Meter – This system uses a capacitance probe

and an electronic (LED) readout to measure and display the

LOX level by pressing the onboard operate button.

5. Filling Circuit – This manual covers both the side fill Hi Flow

with the rotary quick disconnect valve and the top fill Hi Flow 

with the push quick disconnect valve for filling.

FIGURE 1: Hi Flow Stroller Components

Summary of Contents for Hi Flow Stroller







































Reviews: