background image

Hi Flow Stroller Technical Service Manual • PN 14314465 Rev 

F

33

H

i F

lo

w S
tr

oller

Service Tools / Equipment / Supplies

X

Required Tools

1. Hex Wrenches (various sizes)
2. Flat Blade Screwdriver
3. 5/16” Nut Driver
4. Open End Wrenches (1/2” to 1-1/8”)
5. Side Cutters
6. Phillips Screwdriver
7. Pliers
8. Torque Driver/Wrenches:

12-17 N-cm (10-15 in-lbs)
23-29 N-cm (20-25 in-lbs)
69-92 N-cm (60-80 in-lbs)
104-115 N-cm (90-100 in-lbs)
6.2-6.9 N-m (45-50 ft-lbs)

9. Jeweler’s Screwdriver

Required Fixtures/Equipment 

1. Capacitance Meter
2. Soldering Iron
3. Oxygen Regulator/Hose Kit
4. Pressure Gauge
5. Pressure Gauge Adapter
6. Flowmeter
7. 02 Gas Source (High Pressure bottle)
8. 02 Liquid Source
9. N2 Gas or Clean, Dry Compressed Air Source
10. Tubing (02 compatible)

Required Supplies 

1. Stay-Clean Flux
2. Cotton Swabs
3. Lead-free Solder
4. Distilled Water
5. Household Glass Cleaner
6. Lint-Free Cloth
7. Teflon® Tape
8. Fluorolubricant
9. Leak Detection Fluid

Tools and Accessories available from CAIRE, Inc.

Part No 

Description

CA200071 

240 AC Fluorolubricant 

CA200072 

”Snoop” Leak Detection Fluid

CA400004 

Replacement Filter/Male Transfer Line Adapter 

CA406308 

10.3 bar (150 psi) Relief Valve Assembly

CA406310 Teflon® Tape
CA406398 

10.3 bar (150 psi) Relief Valve only

14314465 

Service Manual

13214825 

AirLift Backpack

10018138 

C1000 Backpack

97112026 

Female Side Fill Pneumatic Test Adapter

97200076 

Erie “Liter Meter”

97217007 

Pressure Gauge Adapter

97212021 

Male Side Fill Pneumatic Test Adapter

97403015 

Capacitance Meter

97403016 

Jeweler’s Screwdriver

97405279 

Pneumatic Hose with DISS Fittings

97403574 

Dewar Cap

97403577 

0-4.1 bar (0-60 psig) Pressure Gauge

12917730 

Stroller Cart

97405147 

0–45 psig Oxygen Regulator

97405431 

Liquid Oxygen Transfer Line – 2 m (6 ft)

97404564 

Transfer Line Swivel Connector

97405590 

Lip Seal Service Tool

97406471 

Tandem Tee Kit

97406555 

Super Flex Liquid Oxygen Transfer Line – 6’

97406630 

Dual Fill Head Tee

13329091 

G4 Capacitance Meter Adaptor Kit

Summary of Contents for Hi Flow Stroller







































Reviews: