background image

If arming is enabled, then arming is performed, or the exit delay interval is started, which is accompanied by a
sound, LED and screen indication.

If arming is prohibited, then a sound indication of the rejection is made, and the reason for which the arming is
impossible is displayed on the keypad screen.

Arming and Disarming with Partition Selection

If several partitions are assigned to the user code, then first the user shall select the partition, which state he/she
wants to change, and then type the code.

To select a partition, the user shall first enter the number of the partition, which state he/she wants to change, and
then click the “#” button.

Let’s suppose that the user wants to disarm partition number 2 using the code 1234. To do this, he/she
shall press the following sequence of buttons on the keypad: 2 # 1234

If the user types the correct code with several partitions assigned, but previously he/she has not selected the
partition, which state shall be changed, then such code is treated as incorrect.

Arming Rejection

“Arming rejection” is the impossibility to arm the site, if the security alarm on the site is faulty, or arming is
prohibited due to lack of payment for security services.

There are the following reasons for arming rejection:

malfunction of one or more zones;

alarm in one or more zones;

no communication with the panel program via IP channel;

absence of 220V on the site;

no payment for security services;

the device case is opened.

2.3.2

LED Indication

There are two LEDs on the K16-LCD keypad: “Emergency” and “Arm”.

“Arm” LED

The LED has two display modes: standby mode and arming mode.

In standby mode, the “Arm” LED displays the status of the entire device:

if only one partition is configured for the device, the LED is on, if this partition is armed, and turned off if
disarmed;

if several partitions are configured for the device, the LED is on, if all partitions are armed, and turned off if
at least one partition is disarmed;

if none of the conditions described above are met, then the LED is off.

In the arming mode, the LED “flashes rapidly” during the exit delay.

17

Summary of Contents for GSM





































































































Reviews: