background image

13

40÷60 cm

Description

Pair of photocells for detection of obstacles for automations 
for doors and gates. 

The pair is made up of a transmitter (labelled TX) that 
sends and infrared ray towards the receiver (labelled RX).  
The receiver has an output with NC contact (normally closed). 
The interruption of the ray causes the contact to open, the 
control unit detects the receiver switch-over and interrupts the 
movement according to the settings selected.
Installation
Open the photocells by using a screwdriver as a lever in the 
slot

The difference between the receiver and the transmitter is evi-
dent from the number of clamps present on the boards:
4 clamps for the receiver (RX)
2 clamps for the transmitter (TX)

The two photocells must be fixed on the outside and as near 
as possible to the gate:

Trace the drilling holes using the pho-
tocell base as a reference. 
The hole in proximity of the terminal 
board must correspond to the passage 
of the cables.
Four 6 mm plugs and relative screws 
are supplied for fixing the photocells.

Make two holes with diam-
eter of 6 mm  in a way that 
the hole in proximity of the 
terminal board corresponds 
to the set-up of the cables.
Insert the cable and fix the 
base of the photocell to the 
wall using the plugs and 
screws.

Connections

Connect the TX and RX to the control unit as per the main con-
nection layout.
TX only requires power supply from the 24V output of the control 
unit, respect the polarities (+/-).
RX requires 24V power supply (respect the pola/-) and 
the connection of the NC contact at the PHOT C input.

(TX)

(RX)

Installation of photocells P.BY

(RX)

(TX)

Make the connections and re-position the covers checking that 
the cover with the lens (RX - 4 clamps) is applied to the receiver. 
The lens can be recognised by the concentric circles that are 
visible in transparency. 

4

2

At a height of 40÷60 cm from the ground:

(RX)

(TX)

TECHNICAL DATA

P.BY photocells

Power supply

24Vac/dc 

Capacity
(in optimal conditions)

about 20 metres

Absorption

15mA(TX) - 20mA(RX)

Functioning temperature

-20°C / +70°C

Protection rating

IP44

Dimensions

90x35x31 (mm)

Summary of Contents for BEAUTY





























Reviews: