BWT OCTO +450 Installation And Operating Instructions Manual Download Page 27

Page: 27 / 44

27/44

2020/09- Version: L Code : 97112223

HOTLINE

BWT myPOOL

TROPIC WOODEN POOLS

13.5

Pipe connections

1 = skimmer

2 = return fittings

Connect the rigid descending pipes to the filtration group as shown above. The roll of tubing provided in

the Filtration kit is sized for a standard installation, that is to say, with the filter group located 3.5 m from the

pool (minimum distance between the pump and the pool according to the French electrical safety standard

C15-100 if the filtration group is not installed in a locked plant room).

Tip:

You may use silicon grease or soapy water to help fit the pipes together.

14.

FITTING THE COPING

Note the distribution of the various modules constituting the coping on the drawing. Arrange them on the

coping support brackets. Make sure that the elements are correctly and evenly positioned around the entire

periphery of the pool. Adjust them if necessary and make sure that they remain in position until screwed in.

Summary of Contents for OCTO +450













































Search results

Summary of Contents for OCTO +450

Reviews:

Brands by name

Popular brands

BWT OCTO +450, Installation And Operating Instructions Manual

Search results

Summary of Contents for OCTO +450

Reviews:

Brands by name

Popular brands