Buderus Logamatic 4211 Operating Instructions Manual Download Page 66

Page: 66 / 80

Modules and their functions

Logamatic 4211 - Subject to technical modifications.

Heating circuit and DHW function

Heating circuit and DHW switch

The positions

and

manual

are special settings

reserved for heating contractors only.

Current functions are indicated by LEDs.

As the base load, only the first stage will be
enabled for single and two-stage burners.
The second stage is at zero volts. The burner
servomotor cannot be reversed. For
modulating burners, the burner output can be
infinitely increased using

and infinitely

reduced using

AUT:

The burner operates in automatic mode.

The burner is switched OFF. Except when
the burner emergency switch is set to

max I+II: The burner operates continuously at

maximum output.

USER INFORMATION

In standard mode, the switch should be set
to "AUT".

Heating circuit 0 or boiler pump and cylinder
primary pump are switched on.

AUT:

Heating circuit 0 or boiler circuit and DHW
circuit operate in automatic mode.

Only heating circuit 0 or boiler pump, cylinder
primary pump and DHW circulation pump are
switched off.The control functions continue to
operate.

"Flue gas test" (explanation

chapter 10).

Summary of Contents for Logamatic 4211

















































































Search results

Summary of Contents for Logamatic 4211

Reviews:

Related manuals for Logamatic 4211

Brands by name

Popular brands

Buderus Logamatic 4211, Operating Instructions Manual

Search results

Summary of Contents for Logamatic 4211

Reviews:

Related manuals for Logamatic 4211

Brands by name

Popular brands