Buderus Logamatic 4211 Operating Instructions Manual Download Page 70

Page: 70 / 80

Troubleshooting

Logamatic 4211 - Subject to technical modifications.

11.1 Simple troubleshooting

If no fault messages are displayed on the control
unit in spite of cool rooms or cool DHW, there may
be an incorrect setting.

Observation

Possible cause(s)

Measure

Control unit remains dark or does
not function

–

ON/OFF switch set to "OFF".

–

No power supply.

–

ON/OFF switch set to
"ON".

–

Check mains electrical
fuse.

–

Heating system
emergency stop switch
set to "ON".

MEC2 display dark

–

MEC2 incorrectly plugged in (contact
problems).

–

Fit MEC2 correctly.

Room cool

–

Actual room temperature for the
corresponding heating circuit is
incorrectly displayed.

–

Check the heating circuit
assignment.

–

Control unit operates in setback mode.

–

Check time and heating
program, and modify if
required.

–

Set room temperature too low.

–

Correct set room
temperature.

–

DHW supply runs too long.

–

Check DHW heating.

–

Heat sources deliver insufficient heating
energy or are shut down.

–

Check heat source.

–

Room temperature sensor is incorrectly
adjusted.

–

Sensor adjustment.

DHW cool

–

DHW is set to the wrong temperature.

–

Correct the DHW
temperature setting.

–

Switching program is incorrectly set up.

–

Re-program the switching
program.

DHW cool
(if DHW is heated by external heat
source)

–

External heat sources supply insufficient
heating energy.

–

Check heat source.

Tab. 3

Simple troubleshooting

Summary of Contents for Logamatic 4211

















































































Search results

Summary of Contents for Logamatic 4211

Reviews:

Related manuals for Logamatic 4211

Brands by name

Popular brands

Buderus Logamatic 4211, Operating Instructions Manual

Search results

Summary of Contents for Logamatic 4211

Reviews:

Related manuals for Logamatic 4211

Brands by name

Popular brands