BTI Wireless CP880-B LTE CPE User Manual Download Page 53

Page: 53 / 53

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference, and 2) This device must accept any

interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communication. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by BTI could void the user

’

s authority

to operate the equipment.

FCC Radiation Exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 50cm

between the radiator and your body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Summary of Contents for CP880-B LTE CPE






















































Search results

Summary of Contents for CP880-B LTE CPE

Reviews:

Related manuals for CP880-B LTE CPE

Brands by name

Popular brands

BTI Wireless CP880-B LTE CPE, User Manual

Search results

Summary of Contents for CP880-B LTE CPE

Reviews:

Related manuals for CP880-B LTE CPE

Brands by name

Popular brands