Bruno SRE-2700 Page 3 Installation Manual Download | Manualshive

Page: 3 / 57

background image

©2004,2002 BRUNO INDEPENDENT LIVING AIDS, INC.®

3

SRE-2700 06-11-2004

IMPORTANT NOTES

................................................................................... 2

INTRODUCTION

.......................................................................................... 4

TECHNICAL SPECIFICATIONS

.................................................................. 5

CARTON CONTENTS

................................................................................. 6

OVERVIEW

.................................................................................................. 7-8

INSTALLATION

.......................................................................................... 9-30

Tools Necessary for Installation................................... 9
Bumper Bracket Installation......................................... 10
Fitting the Rail.............................................................. 10
Application Guide......................................................... 11-12
Cutting the Rail............................................................. 13
Rail Joint Assembly...................................................... 14
Positioning Foot Clamp Assemblies............................. 15-17
Mounting the Carriage on the Upper Rail..................... 18-19
Adjusting the Carriage Angle........................................20
Installing the Seat Assembly........................................ 20-22
Installing the Final Limit Ramp and Switch.................. 22
Connecting the Power Source..................................... 23-24
Testing the Unit............................................................ 25
Infrared Call/Send Transmitter..................................... 26
Mounting the Standard Call/Send Transmitter............. 27
Learning the Standard Call/Send Transmitter.............. 28-29
When the Installation is Complete............................... 29
Lubrication................................................................... 30

ELECTRICAL

............................................................................................... 31-34

Converting Rail/Carriage for Right-Hand Operation..... 31
Converting Rocker Switch to Left Armrest................... 32
Circuit Breaker............................................................. 33
Wiring Schematic......................................................... 34

LONG-TERM STORAGE

............................................................................. 35

TROUBLESHOOTING

................................................................................. 36-37

YEARLY MAINTENANCE OPERATIONS

................................................... 38

EXPLODED VIEW AND BILL OF MATERIALS

.......................................... 39-56

LIMITED WARRANTY

................................................................................. 57

TABLE OF CONTENTS

«
1
2
3
4
5
...
»

Summary of Contents for SRE-2700


























































Reviews:

No comments

Related manuals for SRE-2700

Victorian Outdoor Elevator

Brand: AmeriGlide Pages: 39

Brand: XCMG Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands