manualshive.com logo in svg

Brother HS-3000, Service Manual, Page: 6 / 164

Share
Download
Brother HS-3000 Service Manual Download Page 6

iii

Needle-presser unit attachment ......................................................................................................... 3 - 7
Upper shaft assy. attachment  ............................................................................................................ 3 - 8
Feed unit assy. attachment  ................................................................................................................ 3 - 9
Spring attachment  ............................................................................................................................. 3 - 9
Upper shaft and lower shaft phase matching .................................................................................. 3 - 10
Tension pulley assy. attachment  ..................................................................................................... 3 - 10

Tension pulley assy. assembly   ................................................................................................. 3 - 10

Main motor assy. attachment  .......................................................................................................... 3 - 11

Main motor assembly ................................................................................................................ 3 - 11

FC jack attachment  ......................................................................................................................... 3 - 11
Inlet assy. attachment ...................................................................................................................... 3 - 11
Power PCB assy. attachment  .......................................................................................................... 3 - 12

Power PCB assy. assembly   ...................................................................................................... 3 - 12

Main PCB assy. attachment  ............................................................................................................ 3 - 13
Upper cover thread guide attachment ............................................................................................. 3 - 13
Base plate rubber attachment  .......................................................................................................... 3 - 13
Panel cover assy. attachment  .......................................................................................................... 3 - 14

Panel cover assy. assembly  ....................................................................................................... 3 - 14

SV keytop attachment ..................................................................................................................... 3 - 15
Mode select PCB assy. attachment  ................................................................................................. 3 - 15
Single light guide assy. attachment ................................................................................................. 3 - 15
Selecting and manual buttons attachment ....................................................................................... 3 - 16
Operation PCB assy. attachment  .................................................................................................... 3 - 16
LED lamp attachment  ..................................................................................................................... 3 - 16
Buttons attachment  ......................................................................................................................... 3 - 17
SSVR PCB assy. attachment  .......................................................................................................... 3 - 18
Thread guide assy. B attachment  .................................................................................................... 3 - 18

Thread guide assy. B assembly  ................................................................................................. 3 - 19

Thread guide assy. A attachment .................................................................................................... 3 - 20

Thread guide assy. A assembly  ................................................................................................ 3 - 20

Front cover assy. attachment  .......................................................................................................... 3 - 21
Face plate A assy. attachment ......................................................................................................... 3 - 22

Face plate A assy. assembly  ..................................................................................................... 3 - 22

Needle plate B assy. attachment  ..................................................................................................... 3 - 23

Needle plate B assy. assembly  .................................................................................................. 3 - 23

Base cover attachment  .................................................................................................................... 3 - 23
Accessory table attachment  ............................................................................................................ 3 - 24

Feed unit ......................................................................................................... 3 - 25

Lower shaft bushing attachment  ..................................................................................................... 3 - 26
Lower shaft assy. attachment .......................................................................................................... 3 - 26
Timing pulley D attachment  ........................................................................................................... 3 - 26
FPM holder assy. attachment .......................................................................................................... 3 - 27

FPM assembly  .......................................................................................................................... 3 - 27

Vertical lever attachment  ................................................................................................................ 3 - 28
Feed adjuster assy. attachment ........................................................................................................ 3 - 29

Feed adjuster assy. assembly ..................................................................................................... 3 - 29

Feed arm A assy. attachment  .......................................................................................................... 3 - 30

Feed arm B assy. assembly  ....................................................................................................... 3 - 31

Needle plate supporter shaft B attachment ..................................................................................... 3 - 32
FPM gear engagement  .................................................................................................................... 3 - 33
Feed bar attachment  ........................................................................................................................ 3 - 34
Shaft supporter attachment  ............................................................................................................. 3 - 34
Outer rotary hook attachment  ......................................................................................................... 3 - 34
Vertical adjuster screw assy. attachment ........................................................................................ 3 - 35
Feed dog attachment  ....................................................................................................................... 3 - 35
Inner rotary hook bracket assy. attachment .................................................................................... 3 - 35

Summary of Contents for HS-3000





































































































































































Reviews:

No comments