Brother FAX 560 Service Manual Download Page 149

Page: 149 / 194

- 16

2.4

Troubleshooting Procedures

[ 1 ] Control panel related

Trouble

Check:

(1) LCD shows nothing.

• Panel-main harness between the main PCB and the control PCB
• Interfaces between the main PCB, NCU PCB and power supply

PCB

• LCD
• Control panel PCB
• Power supply PCB
• NCU PCB
• Main PCB

(2) Control panel inoperative.

• Panel-main harness between the main PCB and the control PCB
• Interfaces between the main PCB, NCU PCB and power supply

PCB

• Control panel PCB
• FPC key
• Main PCB

[ 2 ] Telephone related

Trouble

Check:

(1) No phone call can be made.

• FPC key
• Control panel PCB by using the maintenance-mode function

code 13. If any defective keys are found, replace them. (Refer

to Chapter V, Section 3.7, "Operational Check of Control Panel

PCB.")

• NCU PCB
• Main PCB

(2) Speed dialing or one-touch

dialing will not work.

• Ordinary dialing function (other than the speed and one-touch

dialing)
If it works normally, check the main PCB; if not, refer to item (1)

above.

(3) Speaker silent during on-hook

dialing.

• Ordinary dialing function (Pick up the handset and press the

numerical keys.)
If it works normally, proceed to the following checks; if not, refer

to item (1) above.

(4) Dial does not switch between

tone and pulse.

• Main PCB
(Not supported by the U.S.A. versions.)

(5) Telephone does not ring.

• Speaker
• NCU PCB
• Main PCB

Summary of Contents for FAX 560



































































































































































































Search results

Summary of Contents for FAX 560

Reviews:

Related manuals for FAX 560

Brands by name

Popular brands

Brother FAX 560, Service Manual

Search results

Summary of Contents for FAX 560

Reviews:

Related manuals for FAX 560

Brands by name

Popular brands