Brother FAX 560 Service Manual Download Page 102

Page: 102 / 194

- 30

WSW16

(Function setting 1)

Selector

No.

Function

Setting and Specifications

Not used.

CCITT superfine recommendation

0: OFF

1: ON

Not used.

Max. document length limitation

0: 400 cm

1: 90 cm

Stop

key pressed during reception

0: Not functional

1: Functional

Selector 2:

CCITT superfine recommendation

If this selector is set to "1," the equipment communicates in CCITT recommended superfine mode
(15.4 lines/mm). If it is set to "0," it communicates in native superfine mode.

Selector 7:

Max. document length limitation

This selector is used to select the maximum length of a document to be sent.

Selector 8:

Stop key pressed during reception

If this selector is set to "1," pressing the

Stop

key can stop the current receiving operation. The

received data will be lost.

Summary of Contents for FAX 560



































































































































































































Search results

Summary of Contents for FAX 560

Reviews:

Related manuals for FAX 560

Brands by name

Popular brands

Brother FAX 560, Service Manual

Search results

Summary of Contents for FAX 560

Reviews:

Related manuals for FAX 560

Brands by name

Popular brands